Router1
interfaces Configuration
Ø Router1(config)#interface serial 0/0
Ø Router1(config-if)#description CONNECTED TO
FRAME-RELAY SWITCH
Ø Router1(config-if)#encapsulation frame-relay {Dedicate
only for Frame-relay}
Ø Router1(config-if)#no shutdown
Ø Router1(config-if)#exit
Point-to-Point Sub Interfaces
Configuration in Router1
Ø Router1(config)#interface serial 0/0.102 point-to-point
ü 0/0.102: - Sub interface any no. and
Point-to-Point for Frame-relay configuration
Ø Router1(config-if)#description CONNECTED TO FRAME-RELAY SWITCH
Ø Router1(config-if)#ip address 100.100.100.1 255.255.255.0
Ø Router1(config-if)#frame-relay interface-dlci 102 {specify the
Local DLCI no.}
Ø Router1(config-if)#exit
Point-to-Point
Sub Interfaces Configuration in Router1
Ø Router1(config)#interface serial 0/0.103 point-to-point
Ø Router1(config-if)#description CONNECTED TO
FRAME-RELAY SWITCH
Ø Router1(config-if)#ip address 200.200.200.1 255.255.255.0
Ø Router1(config-if)# frame-relay interface-dlci 103
Ø Router1(config-if)#exit
Router2 interfaces
Configuration
Ø Router2(config)#interface serial 0/2
Ø Router2(config-if)#description CONNECTED TO
FRAME-RELAY SWITCH
Ø Router2(config-if)#encapsulation frame-relay {Dedicate only
for Frame-relay}
Ø Router2(config-if)#no shutdown
Ø Router2(config-if)#exit
Point-to-Point Sub Interfaces
Configuration in Router2
Ø Router2(config)#interface serial 0/2.201 point-to-point
Ø Router2(config-if)#description CONNECTED TO
FRAME-RELAY SWITCH
Ø Router2(config-if)#ip address 100.100.100.2 255.255.255.0
Ø Router2(config-if)# frame-relay interface-dlci 201
Ø Router2(config-if)#exit
Router3 interfaces
Configuration
Ø Router3(config)#interface serial 0/3
Ø Router3(config-if)#description CONNECTED TO
FRAME-RELAY SWITCH
Ø Router3(config-if)#encapsulation frame-relay {Dedicate only for
Frame-relay}
Ø Router3(config-if)#no shutdown
Ø Router3(config-if)#exit
Point-to-Point Sub Interfaces
Configuration in Router3
Ø Router3(config)#interface serial 0/3.301 point-to-point
Ø Router3(config-if)#description CONNECTED TO
FRAME-RELAY SWITCH
Ø Router3(config-if)#ip address 200.200.200.2 255.255.255.0
Ø Router3(config-if)# frame-relay interface-dlci 301
Ø Router3(config-if)#exit
Routers
1 2 and 3 configurations is done
Now we Configure
Frame-Relay Switch {which is
Actually a Router} Act as a Frame-relay Switch
This is Actually ISP Side Configuration
Ø
FRSW(config)#frame-relay
switching {enable
Frame-relay Switching}
Ø FRSW(config)#interface s0/0
Ø FRSW(config-if)#description CONNECTED TO Router1
Ø FRSW(config-if)#encapsulation frame-relay
Ø FRSW(config-if)#frame-relay intf-type dce {DCE :- for
give a Clock Rate}
Ø FRSW(config-if)#clock rate 64000
Ø FRSW(config-if)#frame-relay route 102
interface serial 0/1 201 {Routing}
Ø FRSW(config-if)#frame-relay route 103
interface serial 0/2 301 {Routing}
Ø FRSW(config-if)#no shutdown
Ø FRSW(config-if)#exit
Ø FRSW(config)#interface s0/2
Ø FRSW(config-if)#description CONNECTED TO Router2
Ø FRSW(config-if)#encapsulation frame-relay
Ø FRSW(config-if)#frame-relay intf-type dce
Ø FRSW(config-if)#clock rate 64000
Ø FRSW(config-if)#frame-relay route 201
interface serial 0/0 102
Ø FRSW(config-if)#no shutdown
Ø FRSW(config-if)#exit
Ø FRSW(config)#interface serial 0/3
Ø FRSW(config-if)#description CONNECTED TO Router3
Ø FRSW(config-if)#encapsulation frame-relay
Ø FRSW(config-if)#frame-relay intf-type dce
Ø FRSW(config-if)#clock rate 64000
Ø FRSW(config-if)#frame-relay route 301
interface serial 0/0 103
Ø FRSW(config-if)#no shutdown
Ø FRSW(config-if)#exit
Now Our Routers and Frame-Relay
Configuration is done
Troubleshooting Command
Ø Router# show frame-relay lmi
Ø Router# show frame-relay map
Ø Router# do show frame-relay pvc
Now
Ping Router1 2 & Router3
Any Routing Protocol is running on
Network {EIGRP, OSPF to connectivity with Routers Internal Networks
0 comments:
Post a Comment